Versions Compared

Version Old Version 33 New Version 34
Changes made by

Julie Isebaert

Koen Matthijs

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

A huge chunk of the general introduction on Sensor Installation that has been presented during the Cobundu Summer 2021 Sessions was about Motion Tabs Installation, this is the recording: Summer 2021 Session: Sensor Installation

Installation Flow

General

1. Decide HOW to install
• Check if locations apply to prerequisites described in this document. If there are any deviations to these prerequisites, please contact your Implementation Consultant at Spacewell with a description and, ideally, pictures of the situation

...

French version : Motion Tab Guide d Installation.pptx

 

 

Workplace

Always check the detailed instruction in the Motion Tab Placement Guide.

If the situation you are facing deviates from these instructions/prerequisites, please contact Spacewell. Pictures / Drawings say more than a 1000 words.

 

1.Go to the workplace

...

  • Sensor unpack & placement indication
  • Take sticker from packaging and stick it to the sensor plan
  • Remove sensor from packaging
  • Tape placement
  • Cap placement (different for "normal" vs "height adjustable" tables!): to install the cap on the sensor, just pull the strip, exposing the adhesive.
  • Sensor placement
    • underneath normal table (between 60-80 cm high (not height adjustable to standing table)): vertical/ downwards + perpendicular to table (short side sensor parallel to long side table)
    • underneath height adjustable table: longest face of the sensor is parallel to the front of the desk and the lens facing downwards (long side sensor parallel to long side table)

Meeting room

Always check the detailed instruction in the Motion Tab Placement Guide.

If the situation you are facing deviates from these instructions/prerequisites, please contact Spacewell. Pictures / Drawings say more than a 1000 words.


1.Go to the meeting room
2.Check the height of the meeting room
  • Ceiling height between 2,15m and 4m
  • Length > 4m OR Width > 4m

3.Calculate the prerequisites by comparing the height to the table (Multiple sensors needed when coverage of 1 sensor is exceeded)
4.Check the room against the prerequisites. If the prerequisite “coverage of 1 sensor” is exceeded, multiple sensors must be installed: please contact Spacewell
5.Check for obstructions → contact Spacewell
6.Placement
  • Sensor unpack & placement indication
  • Take sticker from packaging and stick it to the sensor plan
  • Remove sensor from packaging
  • Tape placement
  • Sensor placement on ceiling, in the middle of the room: perpendicular to room (long side sensor parallel to short side room)

Rooms under 4x4m (bubbles, phone booths, concentration rooms, ...)

Always check the detailed instruction in the Motion Tab Placement Guide.

If the situation you are facing deviates from these instructions/prerequisites, please contact Spacewell. Pictures / Drawings say more than a 1000 words.


1.Go to the room
2.Check the height of the room
  • Ceiling height between 2,15m and 4m
  • Length < 4m AND Width < 4m

3.Check the room against the prerequisites. If the prerequisite “Length < 4m AND Width < 4m” is exceeded, please check installation instructions for Meeting Rooms
4.Check for obstructions → contact Spacewell
5.Placement
  • Sensor unpack & placement indication
  • Take sticker from packaging and stick it to the sensor plan
  • Remove sensor from packaging
  • Tape placement
  • Sensor placement on wall of the door, at the entrance of the room
    • Mind that if the door opens to the inside, there might be a reflection on that door. It might be advisable to then place the sensor behind the door (assuming people close the door to start using this space – and thereby trigger the sensor).

Examples

Tape Placement

 

Cap Placement

Workplace (normal)

Workplace (height adjustable table)

 

Sensor Placement

Workplace (normal, not height adj.) placement

Meeting room placement

Rooms under 4x4m placement