Skip to end of metadata
Go to start of metadata

You are viewing an old version of this content. View the current version.

Compare with Current View Version History

« Previous Version 10 Next »

Difficulty: expert

Content

Learning Objectives

After reading this article, you’ll be able to:

  • Prepare your environment to start using MerryIoT Gateway

  • Configure a MerryIoT Gateway

What is MerryIoT Gateway?

MerryIoT Gateway is a LoRa gateway that can be used for any Spacewell LoRa device to connect to the Workplace Platform.

MerryIoT Gateway connects to an existing (guest) Wifi, a seperate wifi network, or to ethernet.

When using WiFi: Since the data between the sensors and the hub is communicated over LoRa network, we assume the impact of this device on the WiFi network will be max 250MB/hub/month.

Unboxing - content

  • MerryIoT Gateway

  • ‪ethernet cable

  • power cord

  • ‪DC-Adapter

Hardware & Network Requirements

MerryIoT Gateways run on 2.4GHz

Open ports 22, 123, 443, 1680 and 1700 in the firewall. These ports only need an outbound connection.

 IP Addresses needed for Outgoing traffic

We sync all our hubs to the same open NTP (network time protocol) servers so we have consistent timings in our data warehouse.

How to use below table

  • as mentioned above, ideally just the ports mentioned should be opened (outbound)

We recommend not to use specific IP addresses or DNS destinations in the firewall as they can and probably will change in the future!

  • protocol information and AL descriptions are extra

Depending on the environment main location, Spacewell Workplace tenants are created in an EU- or US-environment. Hence, for some ports to be opened, the destination address might be a different one:

  • eu: spacewell.eu1.cloud.thethings.industries

  • usa: spacewell.nam1.cloud.thethings.industries

Destination

Port

Protocol

Direction

AL description

HTTP/HTTPS, Webhook

80/443

TCP

Outbound

WEBGUI

 

22

TCP

Inbound/Outbound

SSH

NTP

123

TCP

Outbound

Time Synchronization

  • eu: spacewell.eu1.cloud.thethings.industries

  • usa: spacewell.nam1.cloud.thethings.industries

443

TCP

Outbound

TTI application

1700

TCP

Outbound

Uplink & Downlink Messages

1680

TCP

Outbound

Lora Packet Forwarder

How to Activate the Gateway

Configuration needs to be done on a computer.

Make sure to run through the config settings fairly quickly, else connection will time-out.

Step 1. Device connection

  1. Plug in the device to power

  2. The device will turn up in the WiFi list on your computer

  3. Connect to the MerryIoT wifi. Use the password that is mentioned on the back of the device

  1. Connect in the browser to IP 192.168.4.1

Step 2. LoRa Settings

Gateway ID is visible in this screen

  1. Select “Set LoRa”

  2. Select LoRa Packet Forwarder

  3. Fill the Gateway-Info as in the following picture:

    1. Server address EU: spacewell.eu1.cloud.thethings.industries

    2. Server address Americas: spacewell.nam1.cloud.thethings.industries

  4. Click “Save”

  5. After receiving the “Success” message, go back to the main configuration page

Step 3. Select EITHER Ethernet OR wifi

 For Ethernet selection

  1. Select “WAN”

  2. In Ethernet Settings, select DHCP

  3. Click on the Save button

  4. The device will reboot and the page will look as if it’s stuck (because of the reboot, the “web service” (in the top right corner) will actually be in status disconnected)

  5. The LED on the device will show

    1. power = on/blue

    2. Ethernet LED blue

    3. LoRa LED blue

 For WiFi selection

  1. Make sure to remove any LAN cable; only power supply should be plugged in

  2. Select “Wi-Fi”

  3. All possible networks are visible on the config screen

  4. Select the network you want to connect to and provide the password

  5. Click on the Save button

  6. The device will reboot and the page will look as if it’s stuck (because of the reboot, the “web service” (in the top right corner) will actually be in status disconnected)

  7. The LED on the device will show

    1. power = on/blue

    2. WiFi LED blue

    3. LoRa LED blue

If your configuration was successful:

  • the device will no longer show up in the WiFi scanning list of your computer

  • If your configuration was successful (power = on/blue; WiFi or Ethernet LED blue; LoRa LED blue) the gateway is connected to the LoRaWAN network and is ready to handle packets. Your Spacewell Implementation Consultant can confirm if the gateway is connecting to the Workplace platform (see /wiki/spaces/KB/pages/492072 ).

Additional Information

LED Indicators

  • LED Sequence: Power (System), WAN, Wireless, LoRa

  • Connection through WiFi or WAN, the LED colors should always be: 3 blue lights

    • power on LED: blue

    • WiFi or LAN LED: blue

    • LoRa LED: blue

  • Solid LED indicates a static condition, the blinking LED indicates the system is in upgrading status, or activating the device to link to the corresponding ports

Solid On

Blinking

Off

Power System (blue)

Power ON

Booting

(ignore bootloader)

Power Off

WAN (blue)

Ethernet plug & got IP address

Connecting

Unplugged

Wireless (blue)

WiFi station mode & got IP address

Connecting

Wireless disabled

LoRa (blue)

LoRa is working

Connecting

LoRa is not working

Button Actions

There is only one button (Reset Button) on the back: upon Reset, all the configurations will be gone and you have to do all the configuration settings again.

Troubleshooting

  1. Are you sure the correct ports were opened on the network?

  2. Check the LED lights

  3. Check if the gateway is connected to the correct network (on the switch)

  4. Check if there is network connectivity on the patch in the switch (aka: connect the cable of the patch to your pc)

  5. Replace a non-working hub with one that is confirmed working

    1. If the non-working one is connected to the patch of the working one and this works: there is an issue with the patch/switch

    2. If the working one is connected to the patch of the non-working one and this works: there is an issue with the hub

Hub provisioning

If your hub is not showing up on /wiki/spaces/KB/pages/492072, make sure to communicate the device EUI to the Spacewell support team.

Search


  • No labels